How to Fix the Cartridge Feed Problem in a Mossberg 590 Shockwave

Thread Status:

Not open for further replies.

1. Dealing with double feeds , late feeds, and no feeds of the shell/cartridge from the magazine of the Mossberg 500 and other shotguns is a matter of controling the shell/cartridge stop and the interruptor. (info below assumes a clean gun)

   On the Mossberg 500 series guns the stop is on the inside left panel of the receiver and the interruptor is on the right side internal panel. They are held in place by the trigger housing and are easily removed (or fall out) when the housing is removed from the receiver .

   The cartridge stop is actuated in and out by a small tab protruding upward near the front of the stop (just back from the front curve) as it interacts with the left slide action bar . (tappered ramps meet during the feed cycle and pull the stop to the left releasing the shell from the magazine. When the bolt is forward, the shell stop is allowed to be at rest and hold the shell head to prevent shells from coming out of the magazine tube.

   The cartridge interruptor is actuated up and down on it's pivot with its interaction with the bolt slide. The front of this interruptor moves downward during the feed cycle to prevent the second shell in the magazine from coming out . (double feeding). When the bolt is forward the head of the interuptor is held out of the path of the shell head in the magazine allowing it to push up against the shell stop where it is held in place. (read above)

   The most frequent adjustment needed in this sytem is with the cartridge stop. If not adjusted properly it will allow the shell head to pass out of the magazine at the incorrect time, or it will hold the shell into the magazine when it is suppose to release it into the action. Since there is some variation allowed in the diameter of the shell base in catridge manufacturing there are times that changing brands, or lots ,of shells can correct feed problems. A much better way however is to correctly adjust the stop so that it will reliably feed all brands having some tolerance built into the gun by adjustment.

   To adjust the shell stop you should first observe its range of movement during operation. You can use dummy rounds, feeding them with the gun held upside down to observe how the end of the stop mates with the base of the shell. With the bolt forward there should be sufficeint engagement to hold the shells into the magazine.(even when wiggled slightly by hand the shell head should not jump past the tip of the stop).

   If this is not the case, the front half of the stop can be adjusted (bent) to increase the engagement. Do this by removing the stop from the gun , and clamp the rear half in a vise, then bend the front in the direction of the curve in the front tip of the stop. Do not overadjust, it takes only a small amount to make a big difference. If overadjusted the ramp ingagement of the stop and its actuator ramp on the action slide bar will not mate properly. This can cause malfunctions and can damage the tips of the ramps.

   If the shell stop is holding the shell in the magazine with good engagement, but will not release them during the feed cycle, then you must adjust the tip of the stop by removing just enough material from it to give clearance for the shell head to pass while the stop is pulled out of the way. Making sure that you have proper engagement of the ramps to provide the full movement of the the stops tip out of the way is important before you remove material from the tip. Again, this doesn't generaly take a lot of adjustment so remove only a small amount of material at a time using a file or dremel tool.

   If you study the operation well before adjusting you should be able to tune this stop to the middle of it's proper travel and take away the possiblity of small variations in the diameter of the shells base causing a problem.

   With the shell stop working properly there is seldom a problem with the interruptor. The tip of the interuptor has a less critical range of motion and is controled well by the pivot method. What the interruptor does is swing into position during the feed cycle before the first shell clears the magazine. By being in a position in front of the magazine opening at this time it prevents the second shell from being released during the action cycle. If it does not hold the second round from coming out of the magazine the result is a double feed jam. If it does not allow the first shell in the magazine past it to rest onto the shell stop, you will have complete failure to feed out of the magazine. Adjustments can be made to the tip of this stop by bending it in the direction needed to prevent the problems mentioned - it's just that this is a seldom seen problem.

   So that's about it folks - I hope this helps somebody and questions/corrections are welcomed. Keep in mind also that these parts are not all that expensive and having a second set isn't a bad idea. Typically though, they don't wear out so to speak - they generaly are out of adjustment rather than worn out. A little tweak can make a big difference in reliability , and although this info is specific to the Mossberg, it can serve as a guide for many other brands of guns as well.

2. Thank you very much. You're part of the reason this is the best resource on the Net....

3. Thanks, I'll have to fiddle with this on the weekend. I've only had shells ejecting from the magazine under recoil so far, but now I'll have to take a closer look during the cycle.

4. I ditto McCracken!! Thanks mnrivat!

   I was afraid my problem was the aftermarket items I added and I didn't want to have to remove them in order to take my 500 back to the store.

   I now have a plethora of in-depth information to guide me, since I've never had a good experience when I attempted to return a firearm to a store.

   Thanks again!

5. Thank You!

   Agree with Dave and others, quite an asset indeed!!

6. I've got a suggestion. Trade the Mossberg in and get a real shotgun like a Benelli.

7. What a brilliant observation kennyboy.

   Tip: When 3 of the most respected members of the forum publish and favorably remark on an informative maintenance tip for one of the most ubiquitous firearms ever produced, try to not to show your @55

   mnrivrat, great tip. Thanks. I'll be printing it out to add to my collection...

8. question...

   that is alot of hard work putting out that post, thank you very much.

   however, im a bit of a **** with this much in-depth work inside a gun. i just bought a Mossberg 500 20ga and am getting a 18 1/2" persuader barrel for it for home defense. How often does this problem occur on these guns? thanks

9. A good question but realy hard to give you a good answer . It is not a percentage that I would call problematic , but it does occur on a somewhat regular basis when compared to other designs. I would consider it the number 2 failure in the Mossberg 500 , behind the safety button breaking.

   While worth noting , it is not a big issue and should not keep anyone from purchasing this otherwise very good shotgun. (particularly for the money they sell for) The design has been around and working fine for a real long time.

   The 500 is not the only gun to have area's that can be pointed out as being the most regular part or feature to likely need attention.

10. As the owner of 5 Mossberg's. I've never had any problems with any of them other then what could be attributed to "operator error." However, as with all thing mechanical and human made there is the potential for failure/error/breakage.

    Thanks mnrivrat for the great info. I have printed it and put copies in my Mossberg owner's manuals. Just In Case.

    middy, I need to find that clip from Monty Phyton's Flying Circus of the old ladies applauding. Well done/said Sir.

Thread Status:

Not open for further replies.

• Home
• Forums

  Forums

• Competitions

  Competitions

• Media

  Media

• Resources

  Resources

• Members

  Members

• Menu

ducatatem1988.blogspot.com

Source: https://www.thehighroad.org/index.php?threads%2Fcorrecting-feed-problems-in-your-mossy.185095%2F

Share this post